Skip to main content

1000W Power Amplifier

Circuit Description 1000W Power Amplifier:

Power amplifier has up to 1000 Watt power, this circuit made one channel only so if you want to create a stereo in it must be made one again, actually this is more suitable power amplifier in use for Sound System or outdoor, so if only in use for the house I think is less suitable.
Maybe you've seen or even have an active speaker and there is written 1500 watts PMPO (Peak Music Power Output), make no mistake this is different from Power Amplifier Active Speaker, I often dismantle such Active Speaker in it only a power with power no more than 150 watts by using the transformer 2-3 Ampere. PMPO is not a real power which is issued by the Power Amplifier, but counting all the speakers that there is, for example: if there are 5 pieces of speakers on each channel and each speaker has a power of 10 W then it is 100 W PMPO.

Circuit Diagram 1000W Power Amplifier:

1000W Power Amplifier

Partlist 1000W Power Amplifier:



While this 1000 Watt Power Amplifier minimal use transformer 20 Ampere. And the output of PowerAmplifier DC voltage contains approximately 63 volts, with currents and voltages of this magnitude, this 1000 Watt Power Amplifier will not hesitate hesitate to destroy your woofer speakers to connect. To overcome that then before the speaker on connects to 1000 Watt Power Amplifier must be in pairsSpeaker Protector.
Actually if you want to create a Power Amplifier with great power does not have to make a PowerAmplifier with great power. Example: you want to create a Power Amplifier with 10 000 Watt power. You do not have to assemble a Power Amplifier with power of 10,000 watts, but you assemble thepower Power Amplifier Small but many, such as you assemble the Power Amplifier with 1000 Watts of power for as many as 10 pieces, it will produce 10 000 Watt Power Amplifier helpless.
Circuit uses power transistors pair of 5 x 5 x 2SA1216 and 2SC2922 and 2SC1583 use a differentialamplifier that actually contains 2 pieces of transistors that are in containers together. Why use such built-in amplifier differental tujuanya so identical / similar, could have uses 2 separate transistors but can result in amplifier so it is not symmetrical.
Tips combining speaker.



To get the speakers with great power combining techniques can be used in parallel series, combining each group of speakers should sepaker they will have the same impedance, the same type (Woofer, Mid Range or tweeter) and the same power. Number of merging these speakers should consists of 4 , 9, 16 ff, see picture
Example: The number of speakers have 4 pieces each of its 200 Watt power generated will be aspeaker at = 200 x 4 = 800 Watt. If there are 9 speakers 200 W then the result = 9 x 200 W = 1800Watt.
Labels:

Comments

Post a Comment

Popular posts from this blog

100W Subwoofer Amplifier Circuit Diagram MOSFET

Circuit Description: MOSFET power amplifier circuit based on IRFP240 and IRFP9240 MOSFETs is shown here. The amplifier operates from a +45/-45 V DC dual supply and can deliver 100 watt rms into an 8 ohm speaker and 160 watt rms into a 4 ohm speaker. This Subwoofer Amplifier Circuit Diagram is suitable for a lot applications like general purpose amplifier, guitar amplifier, keyboard amplifier. The amplifier can be also used as a sub woofer amplifier but a subwoofer filter stage has to be added before the input stage. The amplifier has a low distortion of 0.1%, a damping factor greater than 200, input sensitivity of 1.2V and the bandwidth is from 4Hz to 4 KHz. Circuit Features: Assemble the circuit on a good quality PCB. Use a +45/-45 V DC, 3A dual supply for powering the circuit. Power supply voltage must not exceed +55/-55 V DC. Before connecting the speaker, check the zero signal output voltage of the amplifier and in any case it should not be higher than 50mV. If it is h
Post a Comment
Read more

400W Subwoofer amplifier circuit

Features Class-T architecture with proprietary DPP  “Audiophile” Sound Quality  Full Audio Bandwidth, 20Hz to 20kHz  High Efficiency  Supports wide range of output power levels and output loads by changing supply voltage  and external Mosfets  Compatible with unregulated power supplies  Output over-current protection  Over- and under-voltage protection  Over-temperature protection  48-Pin LQFP Package Description The TDA1400 is a one-channel, Amplifier Driver that uses Tripath’s proprietary Digital Power Processing   (DPPTM) technology. The TDA1400 offers higher integration over previous Tripath amplifiers driver   chipsets while providing exceptional audio performance for real world applications. Class-T amplifiers  offer both the audio fidelity of Class-AB and the power efficiency of Class-D amplifiers.  The TDA1400 is typically configured as a single supply, bridged output. This makes the power supply  requirements simpler and maximizes the output power for a giv
Post a Comment
Read more

Subwoofer Amplifier Circuit 400W MOSFET

Subwoofer Amplifier Circuit 400W MOSFET Power amp 400W IRFP448 Circuit Amplifier circuit today,We would like to show you for the MOSFET 400 watt amplifier is amplifier on my kW shares the same circuit and basic PCB layout. The only real difference is the number of output devices to the device. We have using The IRFP448 design while the MOSFET amplifier 14 O / P devices. These amplifiers can be used for virtually any application that requires high performance, low use Noise, distortion and excellent sound quality. Examples would be subwoofer amplifier should FOH stage Amplifiers, surround a canal a very powerful sound amplifier, etc. The 400W MOSFET-amplifier has four key stages of amplification. We are looking to start any Phase appropriate detail. The bias and buffer stage As the name suggests All Q ,C and ZD the Bias and buffer phases. Its main goal is to provide a stable MOSFET Gates and offset voltage and the voltage buffer amplifier stage of the High Resource capac
Post a Comment
Read more