Skip to main content

Car Subwoofer Amplifier 22 Watt

Circuit Description

     The stereo signals coming from the line outputs of the car radio amplifier are mixed at the input and, after the Level Control, the signal enters the buffer IC1A and can be phase reversed by means of SW1. This control can be useful to allow the subwoofer to be in phase with the loudspeakers of the existing car radio. Then, a 12dB/octave variable frequency Car Subwoofer Amplifier Low Pass filter built around IC1B, Q1 and related components follows, allowing to adjust precisely the low pass frequency from 70 to 150Hz. Q2, R17 and C9 form a simple dc voltage stabilizer for the input and filter circuitry, useful to avoid positive rail interaction from the power amplifier to low level sections.
     This unit is intended to be connected to an existing car stereo amplifier, adding the often required extra "punch" to the music by driving a subwoofer. As very low frequencies are omnidirectional, a single amplifier is necessary to drive this dedicated loudspeaker. The power amplifier used is a good and cheap BTL (Bridge Tied Load) 13 pin IC made by Philips (now NXP Semiconductors) requiring a very low parts count and capable of delivering about 22W into a 4 Ohm load at the standard car battery voltage of 14.4V.

Car Subwoofer Amplifier Circuit Diagram



Parts list of Car Subwoofer Amplifier:

  • P1_____________10K Log Potentiometer
  • P2_____________22K Dual gang Linear Potentiometer
  • R1,R4___________1K 1/4W Resistors
  • R2,R3,R5,R6____10K 1/4W Resistors
  • R7,R8_________100K 1/4W Resistors
  • R9,R10,R13_____47K 1/4W Resistors
  • R11,R12________15K 1/4W Resistors
  • R14,R15,R17____47K 1/4W Resistors
  • R16_____________6K8 1/4W Resistor
  • R18_____________1K5 1/4W Resistor
  • C1,C2,C3,C6_____4µ7 25V Electrolytic Capacitors
  • C4,C5__________68nF 63V Polyester Capacitors
  • C7_____________33nF 63V Polyester Capacitor
  • C8,C9_________220µF 25V Electrolytic Capacitors
  • C10___________470nF 63V Polyester Capacitor
  • C11___________100nF 63V Polyester Capacitor
  • C12__________2200µF 25V Electrolytic Capacitor
  • D1______________LED any color and type
  • Q1,Q2_________BC547 45V 100mA NPN Transistors
  • IC1___________TL072 Dual BIFET Op-Amp
  • IC2_________TDA1516BQ 24W BTL Car Radio Power Amplifier IC
  • SW1____________DPDT toggle or slide Switch
  • SW2____________SPST toggle or slide Switch capable of withstanding a current of at least 3A
  • J1,J2__________RCA audio input sockets
  • SPKR___________4 Ohm Woofer or two 8 Ohm Woofers wired in parallel

Technical data:

  • Output power (1KHz sinewave): 22W RMS into 4 Ohms at 14.4V supply
  • Sensitivity: 250mV input for full output
  • Frequency response: 20Hz to 70Hz -3dB with the cursor of P2 fully rotated towards R12, 20Hz to 150Hz -3dB with the cursor of P2 fully rotated towards R11
  • Total harmonic distortion: 17W RMS: 0.5% 22W RMS: 10%

mtx jackhammer subwoofer,jackhammer subwoofer 32,jackhammer subwoofer price,jackhammer subwoofer 24 inch,mtx jackhammer 15 inch subwoofer,mtx 60 inch subwoofer,jackhammer subwoofer pimp my ride,mtx jackhammer 12 inch,

Labels:

Comments

  1. https://bestcarsub.blogspot.com/March 27, 2019 at 3:34 AM

    This blog was very helpful for us. I have liked it very much. We wish to get blogs like this one everyday. Thank you sir. subwoofer

    ReplyDelete

Post a Comment

Popular posts from this blog

100W Subwoofer Amplifier Circuit Diagram MOSFET

Circuit Description: MOSFET power amplifier circuit based on IRFP240 and IRFP9240 MOSFETs is shown here. The amplifier operates from a +45/-45 V DC dual supply and can deliver 100 watt rms into an 8 ohm speaker and 160 watt rms into a 4 ohm speaker. This Subwoofer Amplifier Circuit Diagram is suitable for a lot applications like general purpose amplifier, guitar amplifier, keyboard amplifier. The amplifier can be also used as a sub woofer amplifier but a subwoofer filter stage has to be added before the input stage. The amplifier has a low distortion of 0.1%, a damping factor greater than 200, input sensitivity of 1.2V and the bandwidth is from 4Hz to 4 KHz. Circuit Features: Assemble the circuit on a good quality PCB. Use a +45/-45 V DC, 3A dual supply for powering the circuit. Power supply voltage must not exceed +55/-55 V DC. Before connecting the speaker, check the zero signal output voltage of the amplifier and in any case it should not be higher than 50mV. If it is h
Post a Comment
Read more

400W Subwoofer amplifier circuit

Features Class-T architecture with proprietary DPP  “Audiophile” Sound Quality  Full Audio Bandwidth, 20Hz to 20kHz  High Efficiency  Supports wide range of output power levels and output loads by changing supply voltage  and external Mosfets  Compatible with unregulated power supplies  Output over-current protection  Over- and under-voltage protection  Over-temperature protection  48-Pin LQFP Package Description The TDA1400 is a one-channel, Amplifier Driver that uses Tripath’s proprietary Digital Power Processing   (DPPTM) technology. The TDA1400 offers higher integration over previous Tripath amplifiers driver   chipsets while providing exceptional audio performance for real world applications. Class-T amplifiers  offer both the audio fidelity of Class-AB and the power efficiency of Class-D amplifiers.  The TDA1400 is typically configured as a single supply, bridged output. This makes the power supply  requirements simpler and maximizes the output power for a giv
Post a Comment
Read more

Subwoofer Amplifier Circuit 400W MOSFET

Subwoofer Amplifier Circuit 400W MOSFET Power amp 400W IRFP448 Circuit Amplifier circuit today,We would like to show you for the MOSFET 400 watt amplifier is amplifier on my kW shares the same circuit and basic PCB layout. The only real difference is the number of output devices to the device. We have using The IRFP448 design while the MOSFET amplifier 14 O / P devices. These amplifiers can be used for virtually any application that requires high performance, low use Noise, distortion and excellent sound quality. Examples would be subwoofer amplifier should FOH stage Amplifiers, surround a canal a very powerful sound amplifier, etc. The 400W MOSFET-amplifier has four key stages of amplification. We are looking to start any Phase appropriate detail. The bias and buffer stage As the name suggests All Q ,C and ZD the Bias and buffer phases. Its main goal is to provide a stable MOSFET Gates and offset voltage and the voltage buffer amplifier stage of the High Resource capac
Post a Comment
Read more