Skip to main content

All You Need To Know About Car Subwoofer Filter Circuit

Circuit description:
Here is the circuit diagram of a simple subwoofer filter that can be operated from a 12V DC supply. Such a circuit is very useful in automobile subwoofer applications. The circuit is nothing but a low pass filter whose pass frequency can be adjusted between 60 to 160 Hz. The circuit is designed around the TL072 dual BIFET opamp IC. Out of the two opamps inside the chip, IC1A is wired as a buffer. The left and right audio inputs after mixing is fed to the input of the IC1A using the DPDT switch S1. Switch S1 is the phase control switch which can be used to make the subwoofer in phase with other speakers. When S1 is in position 2, 180 degree phase shift will be induced.POT R7 can be used for controlling the level. IC1B forms the low pass filter whose pass frequency can be controlled by adjusting the dual gang POT R13.

Circuit Features:
  • The circuit can be powered from 12V DC.
  • IC1 must be mounted on a holder.
  • S1 is a DPDT switch.
  • R13 should be a dual gang linear POT.
  • C5 and C6 must be polyester capacitors.
  • POT R13 can be used for adjusting the pass frequency.
  • POT R7 can be used for adjusting the level.
Circuit diagram:

Car subwoofer filter
Labels:

Comments

Post a Comment

Popular posts from this blog

Subwoofer power amplifier circuit diagram

Circuit Diagram Subwoofer power amplifier IC OPA541BM Amplifier Description Subwoofer power amplifier circuit based on IC OPA541BM very suitable for use in subwoofer speakers, these amplifiers possess excellence in sound issued because the sound is very clear and issued in accordance with subwoofer speakers in a low tone.
Post a Comment
Read more

Subwoofer Amplifier Circuit 400W MOSFET

Subwoofer Amplifier Circuit 400W MOSFET Power amp 400W IRFP448 Circuit Amplifier circuit today,We would like to show you for the MOSFET 400 watt amplifier is amplifier on my kW shares the same circuit and basic PCB layout. The only real difference is the number of output devices to the device. We have using The IRFP448 design while the MOSFET amplifier 14 O / P devices. These amplifiers can be used for virtually any application that requires high performance, low use Noise, distortion and excellent sound quality. Examples would be subwoofer amplifier should FOH stage Amplifiers, surround a canal a very powerful sound amplifier, etc. The 400W MOSFET-amplifier has four key stages of amplification. We are looking to start any Phase appropriate detail. The bias and buffer stage As the name suggests All Q ,C and ZD the Bias and buffer phases. Its main goal is to provide a stable MOSFET Gates and offset voltage and the voltage buffer amplifier stage of the High Resource capac...
Post a Comment
Read more

Car Subwoofer Amplifier 22 Watt

Circuit Description      The stereo signals coming from the line outputs of the car radio amplifier are mixed at the input and, after the Level Control, the signal enters the buffer IC1A and can be phase reversed by means of SW1. This control can be useful to allow the subwoofer to be in phase with the loudspeakers of the existing car radio. Then, a 12dB/octave variable frequency Car Subwoofer Amplifier Low Pass filter built around IC1B, Q1 and related components follows, allowing to adjust precisely the low pass frequency from 70 to 150Hz. Q2, R17 and C9 form a simple dc voltage stabilizer for the input and filter circuitry, useful to avoid positive rail interaction from the power amplifier to low level sections.      This unit is intended to be connected to an existing car stereo amplifier, adding the often required extra "punch" to the music by driving a subwoofer. As very low frequencies are omnidirectional, a single amplifier is necessary to dr...
1 comment
Read more